Development and application of technologies for the removal of heavy-metal contaminants from run-off associated with abandoned waste disposal sites - Permeable Reactive Barrier DataEntry ID: ASAC_1300_PRB
Abstract: The contamination of soils by heavy metals is a problem that faces communities the world over. Contamination is of particular concern when it is mobilised into ground and surface waters, where it can migrate into rivers, lakes and the marine environment. Clean up of contaminated sites can exacerbate water pollution by enabling previously immobilised heavy metals to be exposed to water sources. The ... development of adsorption technologies and permeable reactive barriers to remove mobilised pollutants from ground and surface waters, will prevent the spread of contamination from contaminated sites.
The objectives of this research are to develop technology for the containment and treatment of metal contaminated waters at contaminated sites in Antarctica. In this proposal we intend to develop the use of permeable reactive barrier (PRB) technologies for the in situ containment of metal contaminants dispersed from abandoned waste disposal sites, such as at Wilkes and Davis. The scientific findings of this proposal in the years 2003 -2008 indicate that the general principle of cold regions PRB's are sound, but the performance of off the shelf granular media, such as zeolites, are adversely affected by low temperature and freezing. These factors reduce the capacity and kinetics of metal uptake. Zeolites are also limited to the adsorption of metal cations and for example do not adsorb oxy metal anions such as arsenic, chromium etc, which also occur in these areas. Therefore before this technology is applied in Antarctica, modification or development of new material that is robust and predictable in its performance and able to stabilise a broader range of materials in freezing environments is required.
Thus the scientific aims of this proposal are
1. To develop PRB materials applicable for deployment in the Antarctic environment
2. To develop predictive models for predicting the performance of the PRBs
A permeable reactive barrier (PRB) was built and installed in way of a fuel spill located at the Casey Station Main Power House (MPH). This PRB consisted of five cages and was filled with different materials designed to bind and degrade fuel. Each cage had eight multi-ports (MP) throughout its length from which water samples were extracted at different depths, and alongside material samples collected i.e. cage 1 - MP1 to MP 8, Cage 2 - MP9 to MP16. This spreadsheet contains analytical results from 2005 to 2009.
Following are some explanations of the spreadsheets available as part of the download file:
1) PRB Samples - a summary of information i.e. Sample Tracking Database Barcode, label given by sampler, sample type.
2) Nutrients - Water extractable and Potassium Chloride extractable ion concentrations in the PRB material samples given on a dry matter basis (mg/kg).
3) Samples soil only - a summary of samples of material taken from the PRB
4) TPH and total P - Total Petroleum Hydrocarbons (from C9 to C28) and Total Phosphorous concentrations in the PRB material samples given in a dry matter basis (mg/kg)
5) Water Samples - ion concentrations in water samples taken from the barrier from water samples (barcodes link to the summary information)
6) Total P - Total Phosphorous
TPH - Total Petroleum Hydrocarbons
Total P - Total Phosphorous
DMB - Dry Matter Basis
DMF - Dry Matter Fraction
Co-ordinates for the four corners of the lower PRB in lat long:
110 31' 31.672" E
66 16' 54.151" S
110 31' 31.816" E
66 16' 54.129" S
110 31' 32.044" E
66 16' 54.266" S
110 31' 31.903" E
66 16' 54.303" S
All samples were collected within one square metre of these locations.
This work was also associated with ASAC project 2570 (ASAC_2570) - Constraints on hydrocarbon adsorption and nutrient release from zeolites at low temperatures for hydrocarbon remediation in Antarctica. Project 2570 had the following objectives:
The objectives of this research are to further develop low temperature technologies for the containment and remediation of hydrocarbon contaminated waters at contaminated sites in Antarctica. This process requires the examination and development of a number of materials for use in permeable (bio-) reactive barriers and landfarming trials. This process includes; (i) quantification of the nutrient holding capacities of a number of controlled release nutrient products (CRNs); (ii) determination of binary and multi-component exchange equilibria of exchangeable cations with nutrients loaded onto exchange material at low temperatures; (iii) modelling of exchange equilibria using a novel two parameter temperature dependant semi-empirical thermodynamic model; (iv) undertaking dynamic studies and modelling involving exchange material; (v) quantification of adsorption characteristics of Special Antarctic Blend diesel (SAB) emulsions onto barrier media at low temperatures; (vi) the development and understanding of superior hydrocarbon adsorption materials including covalently bonded surfactant modified zeolites and chitson coated sand (vii) determining the effect of petroleum hydrocarbon presence on ion exchange characteristics and the performance of the barrier; (viii) determination of the effect of biofilm growth on ion exchange characteristics and the performance of the barrier (ix) to what extent and how to manipulate ionic strength and composition of ions in solution to achieve optimal release of nutrients for the metabolism of petroleum hydrocarbons by indigenous Antarctic microorganisms; and (x) test and validate the performance of the barrier media under field conditions.
Start Date: 2005-01-01Stop Date: 2009-01-19
Access Constraints These data are not yet publicly available at the URL given below.
Use Constraints This data set conforms to the PICCCBY Attribution License
Please follow instructions listed in the citation reference provided at http://data.aad.gov.au/aadc/metadata/citation.cfm?entry_id=ASAC_130... when using these data.
Data Set Progress
Distribution Media: HTTP
Distribution Size: 315 kb
Distribution Format: excel
Role: TECHNICAL CONTACT
Phone: +61 3 8344 6621
Fax: +61 3 8344 4153
Email: gstevens at unimelb.edu.au
University of Melbourne DEPT OF CHEMICAL ENGINEERING
Province or State: Victoria
Postal Code: 3010
Role: TECHNICAL CONTACT
Role: DIF AUTHOR
Email: mumfordk at unimelb.edu.au
Department of Chemical and Biomolecular Engineering, University of Melbourne
Province or State: Victoria
Postal Code: 3010
Extended Metadata Properties
(Click to view more)
Creation and Review Dates
DIF Creation Date: 2011-11-25
Last DIF Revision Date: 2014-01-10